Kamis, 02 Februari 2012

Golf Grip Tips to Improve Your Game



The golf grip is something which is overlooked. It can be the source of many problems and particularly slicers of the ball. You may or may not have heard some golf grip tips. I have picked up lots through the years and find some effective. The correct golf grip is crucial to perfecting your game and I want to share 7 tips with you.

1. Use The Fingers
People tend to use the palm of the hand more when gripping a club and this can result in problems and a loss of distance. Gripping the club with the palm of the hand will lead to a loss of wrist action which then affects the distance.  You want the wrists involved in the swing and to do this use the fingers more to grip the club. Using the fingers more will increase the amount the wrist can hinge.

2. Gentle Grip
It is simply not true that you have to grip it hard to hit it hard. There are too many people out there guilty of this. Choking down on the club is not the way to go. Gripping the club harder can actually result in a loss of distance and other problems. Find a grip that is just right you are looking for a grip of about 5-6 out of a scale from 1-10.

3. Vardon Grip (Large Hands)
The Vardon grip is a golf grip you may have or not have heard of. It is a well known grip for distance. The grip was made famous by Harry Vardon in the early 20th century. It is a commonly used by professionals and is taught by many professional golf instructors to beginners. It is a grip were the fingers are used more than the palm of the hand.
To perform the Vardon grip all you do is simply put the pinky of the trailing hand and place it between the middle and index finger of the leading hand. For a right handed golfer the trailing hand is the right hand and the left hand is the leading hand. These roles are reversed if you are left handed. The leading hand thumb should fit snugly between the trailing hand. This is a grip which works well for players with larger hands.

4. Check The “V’s”
Always check the “v’s” which are formed by both hands. On the left hand you should be able to see the first two knuckles and the “v” formed by the thumb and index finger should be pointing at your right shoulder. The “v” formed by the right hand should point towards your chin or slightly towards the right shoulder.

5. Baseball Grip (Small Sized Hands)
This is good grip for people with weak wrists and small hands. It’s a grip which is perfect for the beginner who is just learning about the fundamentals of a swing. It is also known as a ten finger grip.
The baseball grip is a simple golf grip to use. Take your grip with the left hand (leading hand) then place the pinky finger of the right hand (trailing hand) close to the index finger of the left hand (leading hand). The thumb of the left hand will then be placed snugly between the right hand.

6. Interlocking Grip (Medium Sized Hands)
This grip locks the hands together but there is also a risk were the club is gripped more with the palm of the hands. It is a good grip for beginners and people with weak wrists and forearms.
It is an easy grip to apply, simply intertwine the pinky of the right hand which is the trailing hand around the index finger of the leading hand. The thumb of the left hand should then fit nicely between the trailing hand (right hand).

7. Forehand Strength Is Key
Strong forehands and wrists will ensure a good powerful grip. Exercising these 2 areas will result in more power.
There are many ways you can exercise these areas but the simplest method I have found is to use a club. Hold the club straight out in front of you with the last three fingers of the left hand. Next step is to use the wrist and move the club up and down about 10 times. Doing this regime 10 times with 3 sets and a minute’s break in-between the set is a sure way to build up the forehand and wrist power. A simple exercise like this will lead to more power and a better grip.

Jumat, 23 September 2011

ISOQAR - The Company



ISOQAR was founded in 1991 as one of the first independent certification bodies in the UK. It now enjoys one of the broadest scopes of accreditation in its industry. In October 2010 ISOQAR was acquired by the Alcumus Group, a multi-disciplinary provider of risk management, compliance and certification services. Today ISOQAR has its own regional auditors throughout the UK and a network of operations across the globe.


Small Businesses

ISOQAR's roots lie in providing a service which is affordable for small to medium-sized businesses. However, the company's pricing structure and its philosophy of being approachable have resulted in organisations of all sizes choosing to work with ISOQAR.


The ISOQAR Approach

Understanding what it is like to be on the receiving end of the audit process, ISOQAR has developed a unique package of benefits for companies seeking registration.


1. Low Costs

ISOQAR's audit fees are amongst the lowest in the industry. Expenses are not normally charged for attending companies' premises and a certificate is provided free to organisations achieving the standard. To comply with accreditation body guidelines, ISOQAR now carries out audits for recertification every three years. Costs for this will be kept to a minimum and discussed with you in advance. Link to FREE Quotation Request


2. Friendly and down-to-earth

There is no need for audits to be traumatic. ISOQAR's assessors are selected for their ability to workwith the quality representative from the company and to be approachable. They establish that the appropriate management system works for the benefit of the company and check it as though they were customers of the firm. Emphasis is firmly placed on practicality.


3. A rapid response

Whether it be a query about system certification, or an urgent need to achieve registration itself, ISOQAR specialises in providing answers or audits at speed. A friendly, helpful administration and management team with expert knowledge are always available at the end of a phone.


4. The use of Industry Experts

When selecting staff for a particular audit, ISOQAR will always choose an auditor with experience of the industry being audited. This ensures that the audit process takes place in an air of mutual understanding. There is no conflict arising from a lack of knowledge of the challenges faced in running that particular business. The auditor and the company being audited both speak the same language.Link to List of Areas of Expertise (Scope)


5. Quality Documents reviewed on site

With the exception of smaller firms, ISOQAR has a policy of visiting companies applying for certification. This enables its documentation (manuals and procedures) to be reviewed and provides an opportunity for the company and the ISOQAR auditor to discuss any areas of concern before the audit itself. Even more importantly, it provides an opportunity to start building a rapport with the auditor

Not only.........but also

In addition to its primary function of providing companies accredited certification to managment standards (including ISO 9001, 14001, 27001, SIA-ACS and BRC Food standards), ISOQAR can offer:
  • Free preliminary visits to companies seeking registration, to discuss what the process involves
  • Low-cost training courses to support its certification services
  • Second party audits to organisations' own quality standards
  • Notified Body audits for Personal Protective Equipment

ISOQAR's track record

ISOQAR has certified thousands of organisations working to the various ISO standards. This number is growing daily. More and more companies are not only realising the benefits of having an approved management system, but also the benefits of using ISOQAR. Its dislike of bureaucracy and its philosophy of being approachable mean that nearly all ISOQAR's contracts stem from recommendations by management consultants or other registered businesses. This has resulted in the company's considerable and stable growth in recent years. Click here to see what our customers say about us.

Integrated Management Systems


An Integrated Management System (IMS) is a single system incorporating the requirements of two or more auditable standards. Any combination that includes at least two of the following standards will be considered to be an integrated system.
Integrated systems will include a combination of:
  • ISO 9001 (Quality)
  • ISO 14001 (Environmental)
  • OHSAS 18001 (Health & Safety)

Benefits of an Integrated System

Elements that are common to all standards enable organisations to benefit from taking a more comprehensive approach to their management system requirements in relation to their daily business activities.
An integrated system is a single documented system that contains a complete policy statement and inclusive objectives combining:
  • Document control
  • Records control
  • Internal auditing
  • Management reviews
  • Process controls and procedural documentation
Benefits of this approach include:
  • Improved communication
  • Training and awareness
  • Improved analysis of data
  • Reduced resource commitment
  • Reduced external audit costs
  • Reduced external surveillance audit requirement

Adding Standards

Your scope of audits can be extended at a later date to include further standards. These may be integrated with your current registration once a certificate has been issued for the new standard(s) following a successful audit.

Want to Know More?

Then please give us a few details about your organisation. We’ll then send you a quote. You won’t be under any obligation and we won’t contact anyone else. Once you have taken us up on our quotation, you can start to benefit from the straightforward and friendly approach to certification that our many customers already enjoy! And as ISOQAR’s fees are highly competitive, free from expenses and ‘extras’, you could start saving straight away.





ISOQAR Achieve a 5-Star Rating from BRC


The BRC British Retail Consortium – Global Standards Team, assess each Certification Body authorised to audit their standards for:
Audit Report Writing Quality
Compliance to the BRC Scheme & Standard protocol requirements
Auditor Registration
Submission of audit reports to the BRC Directory
Commitment and Communication

For the first time they have converted this assessment into a Star rating and have published this information on the BRC Directory which can be viewed at www.brcdirectory.com
Karen Betts Compliance Manager for BRC Global Standards wrote to Steve Stubley Operations Director of ISOQAR
“Your compliance performance rating is 5 stars out a possible 5 star rating. Well done in this achievement, we look forward to maintenance of this high standard and your continued support of the BRC Global Standards.”


This 5 star rating was achieved by only 52% of the Certification Bodies conducting audits against the range of BRC Global Standards in the period January to June 2011.









Senin, 19 September 2011

Safety Slogan

Safety is no accident...
Think before you act...
Safety is forever...
Never forget about safety...
Safety means zero accident...
Keep no accident record...
Remember safety! Your family is waiting for you at home...
Safety is our first priority...
No safety, no business...
Stop accidents before they stop you...
Come safely, work safely and arrive home safely...
Work safely means success...
Keep safety at the first step...
Make your workplace safe and comfort...
Safety is our concern...
With safety, we win...
The safe way is the only way...
Get smart and use safety from the beginning... 
"Say No to Injuries"

Minggu, 18 September 2011

Recommended Format for Material Safety Data Sheet (MSDS)


OSHA's Hazard Communication Standard (HCS) specifies certain information that must be included on MSDS, but does not require that any particular format be followed in presenting this information. In order to promote consistent presentation of information, OSHA recommends that MSDS follow the 16-section format established by the American National Standards Institute (ANSI) standard for preparation of MSDS.

By following this recommended format, the information of greatest concern to workers is featured at the beginning of the data sheet, including information on chemical composition and first aid measures. More technical information that addresses topics such as the physical and chemical properties of the material and toxicological data appears later in the document. While some of this information (such as ecological information) is not required by the HCS, the 16-section MSDS is becoming the international norm. The 16 sections are:

  • Identification 
  • Hazard(s) identification 
  • Composition/information on ingredients 
  • First-aid measures 
  • Fire-fighting measures 
  • Accidental release measures 
  • Handling and storage 
  • Exposure controls/personal protection 
  • Physical and chemical properties 
  • Stability and re-activity 
  • Toxicological information 
  • Ecological information 
  • Disposal considerations 
  • Transport information 
  • Regulatory information 
  • Other information
Section 1: Chemical Product and Company Identification
This section links the chemical name on the label to the MSDS. The MSDS also lists the name, address and the phone number of the company, manufacturer or distributor
who provides the chemical.

Section 2: Composition, Information or Ingredients
This section must identify all the hazardous ingredients of the material. This section may also include OSHA Permissible Exposure Limits (PELs), Threshold Limit Values (TLV), etc.

Section 3: Hazard Identification
This section discusses the health effects one may encounter when exposed to the material. The section will describe the appearance of the material, the potential health effects and symptoms associated with exposure, routes of entry, target organs that could be affected, and so on.

Section 4: First Aid Measures
This section will describe possible first aid procedures for each route of entry. The procedures will be written so that untrained individuals can understand the information.

Section 5: Fire-Fighting Measures
This section will describe information on the fire and explosive properties of the material, extinguishing items, and general fire-fighting instructions.

Section 6: Accidental Release Measures
This section gives information on how to respond when a material spills, leaks or is released into the air. This information may include how to contain a spill or the types of equipment that may be needed for protection.

Section 7: Handling and Storage
This section discusses information on handling and storage of the material. Topics that could be described are: general warnings to prevent overexposure, handling procedures, and hygiene instructions to prevent continued exposure.

Section 8: Exposure Controls and Personal Protection
This section discusses engineering controls and personal protective equipment that would help reduce exposure to the material. The necessary personal protective equipment should be considered for eye/face protection, skin protection and respiratory protection.

Section 9: Physical and Chemical Properties
This section will include information about the physical and chemical properties of the material. The following characteristics should be detailed: appearance, odor, physical state, pH, vapor pressure, vapor density, boiling point, freezing/melting point, solubility in water and specific gravity or density. Indicate if these characteristics do not apply to your material.

Section 10: Stability and Reactivity
This section requires that potentially hazardous chemical reactions be identified. It addresses chemical stability, conditions to avoid, incompatibility with other materials, hazardous decomposition and hazardous polymerization.

Section 11: Toxicological Information
This section discusses data used to determine the hazards that are given in Section 3, “Hazard Identification.” The following information can be addressed: acute data, carcinogenicity, reproductive effects, target organ effects, etc.

Section 12: Ecological Information
This section will help determine the environmental impact should the material ever be released into the environment.

Section 13: Disposal Considerations
This section gives important information that may be helpful in the proper disposal of the material. The information can cover disposal, recycling and reclamation.

Section 14: Transport Information
This section is designed to give basic shipping information. The basic shipping information could include: the hazardous materials description, hazard class and the identification number (UN or NA numbers).

Section 15: Regulatory Information
This section discusses information on the regulations under which the material falls. Examples of a few regulatory agencies are: OSHA, TSCA (Toxic Substance Control Act), CERCLA (Comprehensive Environmental Response, Compensation, and Liability Act), SARA Title III (Superfund Amendments and Reauthorization Act).

Section 16: Other Information
This section should include any other important information concerning the material. This information can include: hazard ratings, preparation and revisions of the MSDS, and label information.

Sabtu, 17 September 2011

8 Main Hazards Faced by Shipyard Workers

Shipyard workers tend to be those working in some of the most risky working environments. This not only adds to the problems of their job but actually makes it a work profile full of need for constant caution.
Working as a ship yard worker is not as simple or easy as it may seem. Here are some of the problems for ship workers that make this job a really hard one:
1.      Working Conditions
Ship yards are not one of the most comfortable places to work in. It is no corner office with glass walls. Instead there is a constant danger in everything a shipyard worker does. The conditions that shipyard jobs offer to work in are not only rather uncomfortable but also dangerous to the workers’ health.
There are several precautions that need to be taken. Sometimes it is extremely cramped spaces while at other times; the mere fall can be high enough to cause serious injury. Extreme nature of working conditions of shipyard workers is the first problem they face.
2.      Timings
Work on shipyards is no nine-to-five job. There are no fixed timings. The extreme nature of their job means the workers have to be available at all times.
The erratic time schedules make this job harder than it already is, and definitely adds to the woes of workers. Sometimes they even have to work for several hours together without much rest.
3.      Machinery Hazard
Ship yards are the places where no work happens at small scale. The machinery used is huge, often requiring immense skill and strength to be handled. A minor discrepancy while working at such machinery can prove to be extremely fatal for any shipyard worker.
The seriousness of injury can be as bad as death, in some cases. Records of workers having been gravely injured date back to as early as 1940s, a time when ship construction really took off all over the world. Constant danger posed by the heavy machinery is what is third problem faced by shipyard workers.
4.      Slips and falls
It would be too much to assume that working on shipyards, in conditions similar to what these shipyard workers work in, minor falls and trips would be rare. However, the seriousness of these minor slips on shipyards is much more compared to somewhere else.
The workers on such ships always run a risk of slipping or falling but here, there are more chances they might not just fall but fall down several feet. Cases of severe injuries like multiple fractures, head injuries, traumatic experiences, amputations and sometimes even drowning have been reported. The risky conditions of work and their vulnerability to injury is the fourth problem faced by workers on shipyards.
5.      Fires and explosions
Ship workers work close to fire and electricity. The high chances of a minor fault going wrong means things can go from bad to worse in a jiffy. Chances of fires, explosions, shot circuit; electric shocks etc are extremely high on shipyards. This high risk of fires and burns becomes another problem for people working on shipyards.
6.      Cramped spaces and high pressure
Most ship workers work just as much in tiny cramped spaces as they do in ridiculously open ones. The cramped spaces (enclosed spaces) are one of the riskiest places to be working in. A shipyard worker, while working in such tiny spaces is often at risk of physical injuries to limbs, head or other body parts along with more serious troubles like suffocation, asphyxiation etc.
Also, the high pressure in such tiny spaces can often cause much more grave and permanent damage like eardrum rupture. Shipyard workers often complain of problems to their hearing abilities due to working constantly under high pressure conditions.
7.      Asbestosis and mesothelioma
Asbestos is used as one of the construction materials for most ships even today. Shipyard workers involved in work of manufacturing of ships and even those not specifically into that particular aspect of shipyard jobs often receive extremely high exposure to asbestos, making them quite vulnerable to diseases caused by it. Asbestosis, along with mesothelioma which is a cancer caused exclusively by asbestos exposure are very serious diseases found mostly in workers working in close proximity to this substance. It is one of the biggest problems faced by workers working in the ship industry especially so since there is still no perfect solution to this problem.
One of the bigger problems with this particular aspect of job is that the symptoms caused due to exposure to asbestos can surface even after many years. Reports of these symptoms showing up in a person up to 50 years after exposure to it have been found. This adds a whole new dimension to this problem making it much more serious.
8.      Improper knowledge
But the biggest problem faced by most of the shipyard workers is that they are mostly unaware about the laws and safety measures made to protect them. In terms of laws enabling them to seek suitable work conditions or the laws that allow them to seek compensation in case of serious injury or just basic information about exposure to hazardous substances like asbestos, the knowledge of these workers is low. This poses as the biggest problem for the workers as it prevents them from finding solutions to most of their other problems.
The problems faced by every worker on shipyards are immense but their implications are even bigger. With correct measures, a lot of these problems can be tackled but there is still a long way to go.